Technifast provides fixings to support world record attempt 04 May 2018

Technifast is manufacturing fixings and inserts to secure Team Britannia’s massive inflatable tubes to the outside of its boat on the team’s round the world record attempt for the fastest powerboat to circumnavigate the globe.

The fixings and inserts from Technifast have been specifically developed to allow the fitting of the two white tubes, which each weigh around 250kg, to the side of boat, without large numbers of people working on either side of the hull. This is important as should either tube be damaged during the 23,000 nautical mile record attempt, the crew need to be able to replace the tubes without putting the vessel into a dry-dock.

The announcement was made at the Aluminium Boatbuilding Company on Hayling Island, where the 80ft RIB is being built, by ocean racing legend and Team Britannia’s skipper Alan Priddy and Technifast’s Senior Engineer, John Garner.

“We encountered an issue attaching our two huge inflatable tubes to the port and starboard sides of the boat. The hull of the boat is constructed from 6mm aluminium plate, and the fixing plates for the tubes required M10 bolts to be used. Tapping directly into the aluminium hull with M10 bolts would not be strong enough, as the softness of the aluminium material coupled with the constant slamming of the boat, would pose a risk of the bolts stripping the threaded aluminium and pulling out. If that was not enough, we needed a fitting that would allow the crew to remove and replace the tubes without having to take the boat out of the water,” explained Alan.

After conversations between Alan and Technifast’s Senior Engineer, John Garner, a design was finalised for an insert, which would increase the holding strength in the aluminium, but still allow the M10 fixings to be used to hold the two tubes in place. Crucially, it will give the option to release the tubes quickly in an emergency and for easy replacement.

“As soon as it became clear what Team Britannia were attempting to do we were delighted to offer our services and support as a partner to this record attempt. The new design, uses a larger metric external thread to give more surface area and better grip. We also removed all undercuts and extended the exterior thread length to ensure that every available millimetre of the insert will provide hold to the relatively thin and light hull of the boat. The increased strength also means that the inserts only need to be installed at 750mm intervals over length of the boat, along the top of the hull with the holding plate bolted on. The tubes can then be attached and removed with relative ease,” said John Garner.

Team Britannia are using a boat designed by Hampshire based Professor Bob Cripps, former Technical Director of VT Halmatic. It will slice the waves, rather than surfing them, with its super-efficient design, a variant of the “fast displacement hull.” This reduces fuel consumption by up to 30%, and should make the 23,000 nautical mile trip smoother.

Construction of the 80ft RIB started in 2015 on Hayling Island, near Portsmouth, at the Aluminium Boatbuilding Company. The hull was completed and turned in December 2016 allowing the completion of over 2,000 closing brackets. The installation of the final bulkhead and six massive fuel tanks is under way, but needs to be completed. Once fitted, the next job will be to install the engines and jets, before the wheelhouse is craned into place.

The fixing and inserts from Technifast will be installed at 750mm intervals over length of the boat, along the top of the hull with the holding plate bolted on. The tubes can then be attached to complete the distinctive look.

“The bespoke solution developed by Technifast, is beautifully simple, practical and most importantly effective. Yet again we are pushing the boundaries to ensure we have a boat that is both light and incredibly tough. I am delighted to be working with another Great British company,” continues Alan.

Claire Aldridge Deputy Editor t: +44 (0) 1727 743 889

Having spent a decade in the fastener industry experiencing every facet – from steel mills, fastener manufacturers, wholesalers, distributors, as well as machinery builders and plating + coating companies, Claire has developed an in-depth knowledge of all things fasteners.

Alongside visiting numerous companies, exhibitions and conferences around the world, Claire has also interviewed high profile figures – focusing on key topics impacting the sector and making sure readers stay up to date with the latest developments within the industry.